Badanie stanu naprężeń własnych po obróbce ubytkowej materiału kompozytowego o osnowie z aluminium zawierającego dodatek ceramiczny *
Residual stress analysis after machining in composite materials based on aluminum alloy with ceramic additive
Mechanik nr 01/2018 - Biuletyn Instytutu Zaawansowanych Technologii Wytwarzania
STRESZCZENIE: W artykule przedstawiono wyniki badań strukturalnych stopu AlSi7Mg z 5% obj. węglika krzemu (SiC) po procesie obróbki ubytkowej z wykorzystaniem metody elektroerozyjnej, strumienia wodno-ściernego i przecinania. Omówiono możliwości pomiaru wpływu wybranych technik obróbki ubytkowej na stan warstwy wierzchniej. Za pomocą dyfrakcji promieniowania rentgenowskiego mierzono poziom i charakter uzyskanych naprężeń własnych. Zaprezentowano metodę dyfrakcji promieniowania X w geometrii stałego kąta padania (SKP), stosowaną w praktyce do pomiaru zakresu zmian w obrębie warstwy wierzchniej, uzyskanej na skutek interakcji pomiędzy narzędziem a powierzchnią obrabianego materiału.
SŁOWA KLUCZOWE: naprężenia własne, stały kąt padania, stop aluminium
ABSTRACT: The paper presents the results of structural studies of AlSi7Mg alloy with 5% vol. addition of silicon carbide (SiC), after the machining process using the alternative method including: electrical discharge machining (EDM), abrasive water jet (AWJ) and cutting. The article presents the possibilities of measuring the impact of selected machining techniques on the surface and subsurface layers. X-ray diffraction were used to determine the level and characters of the obtained residual stresses. The article presents the X-ray diffraction method in the grazing incidence X-ray diffraction technique (GIXD) used for the practical measurement of the range of changes within the surface layer formed, as a result of interaction between the tool and the surface of the material being processed.
KEYWORDS: residual stress, grazing incidence X-ray diffraction technique, aluminum alloy
BIBLIOGRAFIA / BIBLIOGRAPHY:
- Devaraju A., Kumar A., Kotiveerachari B. “Influence of addition of Grp/Al2O3p with SiCp on wear properties of aluminum alloy 6061-T6 hybrid composites via friction stir processing”. Transactions of Nonferrous Metals Society of China. 23 (2013): s. 1275–1280.
- Lieblich M., Corrochano J., Ibáñez J., Vadillo V., Walker J.C., Rainforth W.M. “Subsurface modifications in powder metallurgy aluminum alloy composites reinforced with intermetallic MoSi2 particles under dry sliding wear”. Wear. 309 (2014): s. 126–133.
- Mathan Kumar N., Senthil Kumaran S., Kumaraswamidhas L.A. “Wear behaviour of Al 261 8 alloy reinforced with Si3N4, AlN and ZrB2 in situ composites at elevated temperatures”. Alexandria Engineering Journal. 55 (2016): s. 19–36.
- Manna A., Bhattacharayya B. “A study on machinability of Al/SiC-MMC Journal of Materials Processing Technology”. 140 (2003): s. 711–716.
- Lin J.T., Bhattacharyya D., Lane C. “Case study machinability of a silicon carbide reinforced matrix composite aluminum metal”. Wear. 181–183 (1995): s. 883–888.
- Dolata A.J., Dyzia M. “Aspects of fabrication aluminum matrix heterophase composites by suspension method”. IOP Conf. Series: Materials Science and Engineering. 35 (2012): s. 1–7.
- Dyzia M. “AlSi7Mg/SiC and heterophase SiCP+CG composite for use in cylinder-piston system of air compressor”. Solid State Phenomena. 176 (2011): s. 49–54.
- Skrzypek S. „Nowe możliwości pomiaru makro-naprężeń własnych w materiałach przy zastosowaniu dyfrakcji promieniowania X w geometrii stałego kąta padania”. Kraków: Wydawnictwo Naukowo-Dydaktyczne AGH, 2002.
DOI: https://doi.org/10.17814/mechanik.2018.1.4
* Artykuł recenzowany