Wpływ dodatku EP/AW w warunkach chłodzenia metodą MQCL na morfologię powierzchni stali nierdzewnej 316L *
Effect of EP/AW additive under MQCL cooling conditions on the surface morphology of 316L stainless steel
Mechanik nr 08/09/2016 - X Szkoła Obróbki Skrawaniem, XXXIX Naukowa Szkoła Obróbki Ściernej
STRESZCZENIE: Przedstawiono wyniki badań morfologii powierzchni stali nierdzewnej 316L po toczeniu. Dla zmiennych parametrów skrawania przeprowadzono analizę parametru Sa, krzywej udziału materiałowego oraz gęstości widmowej mocy w zmiennych warunkach chłodzenia: obróbka na sucho, MQCL oraz MQCL + EP/AW. Wykorzystano metodę parameter space investigation (PSI).
SŁOWA KLUCZOWE: obróbka na sucho, MQCL, dodatek EP/AW, morfologia powierzchni
ABSTRACT: The paper presents the results of investigation of the surface morphology 316L stainless steel after turning. For variable cutting parameters Sa parameter, Abbott-Firestone curve and power spectral density were analyzed. The analysis was conducted for variables cooling conditions: dry cutting, MQCL and MQCL + EP/AW. In the research Parameter Space Investigation (PSI) method has been used.
KEYWORDS: dry cutting, MQCL, EP/AW additive, surface morphology
BIBLIOGRAFIA / BIBLIOGRAPHY:
- Masmiati N., Sarhan A.A.D. „Optimizing cutting parameters in inclined end milling for minimum surface residual stress – Taguchi approach”. Measurement. Vol. 60 (2015): pp. 267÷275.
- Kıvak T. „Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts”. Measurement. Vol. 50 (2014): pp. 19÷28.
- Liao Y.S., Lin H.M. „Mechanism of minimum quantity lubrication in high-speed milling of hardened steel”. Int. J. Mach. Tools Manuf. Vol. 47, No. 11 (2007): pp. 1660÷1666.
- Masmiatia N., Sarhan A.A.D., Hassan M.A.N., Hamdi M. „Optimization of cutting conditions for minimum residual stress, cutting force and surface roughness in end milling of S50C medium carbon steel”. Measurement. Vol. 86 (2016): pp. 253÷265.
- Feldshtein E., Maruda R. „Some regularities of the heat transfer in the process of cooling of a cutting zone by an emulsion fog”. J. Eng. Phys. Thermophys. Vol. 79, No. 3 (2006): pp: 606÷610.
- Leppert T. „Effect of cooling and lubrication conditions on surface topography and turning process of C45 steel”. Int. J. Mach. Tools Manuf. Vol. 51, No. 2 (2011): pp. 120÷126.
- Maruda R.W., Legutko S., Królczyk G.M., Hloch S., Michalski M. „An influence of active additives on the formation of selected indicators of the condition of the X10CrNi18-8 stainless steel surface layer in MQCL conditions”. Int. J. Surf. Sci. Eng. Vol. 9, No. 5 (2015): pp. 452÷465.
- Vengudusamy B., Grafl A., Novotny-Farkas F., Schimmel T., Adam K. „Tribological behavior of antiwear additives used in hydraulic applications: Synergistic or antagonistic with other surface-active additives?”.Tribol. Int. Vol. 67 (2013): pp 199÷210.
